Gasoline-powered cars have been the standard vehicles so far, with present and past generations of people driving them and it is quite likely that the next generation may also like to depend on these cars.

Many people are of the view that gasoline-engine cars will still remain the most popular mode of transport. But the truth is that a few decades from now gasoline and for that matter, even petroleum will become very scarce.

In view of this, gasoline-powered cars are not going to last forever. In future more electricity will be generated from renewable sources, such as solar power and wind power and scientists and car manufacturers have established that cars fitted with electric- engines will be the vehicles of the future.

Electric motors have several advantages over conventional internal combustion engines powered by gasoline. In sharp contrast to the gasoline-powered engines, electric cars are 500% more fuel- efficient. In other words, electric cars are more powerful and can run longer distances for smaller amount of power consumption.

As electric engine is run by electricity generated from batteries, solar energy, wind energy or hydro power, it does not emit any harmful gases and therefore, does not pollute the atmosphere. Electric car is noiseless, easy to operate and very safe.

Looking into the immense benefits an electric car can offer, a thought arises that if someone can assemble a number of electrical equipment himself at home, he can as well assemble an electric car himself. If one is enterprising, starting a gas to electric car conversion project can save you thousands of dollars on purchasing a new electric vehicle from a manufacturer.

Before you undertake to construct an electric car as a do-it-yourself exercise, you should examine the option of converting the old car engine into an electrical engine. In majority of cases this can be achieved. You should ensure that you have the necessary know-how to do it on your own. For this, you should have a thorough knowledge of the functioning of a conventional vehicle.

If you have a good experience in repairing your own car, you may be able to initial a gas to electric car project in your home garage. In case, you get the job of car maintenance done by a professional auto repairer, it is advisable to get the electric car built by a professional also. There is no point going through all the headache of trying the complete the DIY EV conversion project yourself.

On the other hand, if you are confident of your skills can take the help of do-it-yourself guide and begin building the electric car, by all mean, go for it!

In order to ensure that your electric car is built properly, a detailed research is required to understand the mechanism of a homemade electric vehicle.

Electric cars have a simple design and therefore, may be simpler to make than a car powered with an internal combustion engine. It may be surprising to know the amount of work that can be done by going through a do-it-yourself kit. The guide will indicate the type of tools and equipment required for making an electrical car.

However, it should be ensured that someone is nearby to assist you in lifting heavy parts and also in handing over tools from time to time during assembly. Garage and a shed with adequate space would be an ideal location to begin the project of building an electric car.

If you need a good step by step instructional guide on EV conversion, check out the book written by Gavin Shoebridge from New Zealand. Shoebridge is known as the EV Guy in the realm of DIY electric car enthusiasts. Click on the link below to visit his web site.

==> Click here to visit Gavin’s web site now!

If you are in search for the method to convert your gasoline car to electric car or would like to know about it, you need to understand the basic parts included in the task. Although it is easy to understand the operation of an electric car and the parts are easy to obtain, there can be problems when you do it in practical. This is what most of us would not like to happen.

There are not many parts which you would need to replace in order to convert your gasoline car into an efficient DIY electric car. The following are 5 parts and components you should never be cheap on.

1) Adapter plate.

The existing transmission of a gasoline car is of no use in an electric car. The adapter plate should be fixed as an aftermarket product.

2) Motor controller.

Electric motors need a motor controller to control the output power it delivers. In electric cars you cannot use transmissions. Most of the golf cars have electric motors.

3) Batteries.

In factory made electric cars the battery system is very complex where as aftermarket fitments use traditional batteries. Batteries are the most important part of an electric car is its battery.

You can choose either lithium-ion battery or gel based battery. Lithium-ion batteries have better performance because it do not contain liquid inside. The gel based batteries eliminate the chances of spilling.

However, a slight concern is that both these batteries are costly. An alternative aftermarket kit is the traditional liquid electrolyte based batteries. Liquid electrolyte batteries need more frequent replacement as it has shorter life compared to the other two batteries.

4) Emergency disconnector.

In cases of an emergency such as a short circuit it is required to immediately disconnect the electric supply between the car motor and the batteries. This is when you will need an emergency disconnector.

5) Electric motor.

Two types of motors are available for you to choose. You can select either an AC motor or a DC motor. AC motors can quickly increase speed after breaking. AC systems have also better power delivery and are easy to install. These have excellent torque too. This makes AC motors quite famous among many converters.

Most of the AC kits can be fitted at your nearest workshop. DC motors are of several advantages as compared to AC motors. They are easy to get and installation is lot easier because most EV converters are using a DC setup. This makes finding an expert in this profession easy. DC motors can mange instantaneous torque.

The lower cost of DC motors makes it more attractive. Choosing the motor which suits your needs should be kept in mind. If you require good power output and better performance you need to go with AC system. Beginners can go for DC motors as it is very easy to install.

In most electric car conversion projects, there is always scope for wielding work as most of the bracing, electric motor supports and other vehicle components are made up of metals and may undergo breakage or require welding after certain period of time. Welding has become a specialized skill and welders who are experienced and best in the business are hired in order carryout all kinds of welding work required.

The welding is a process that has to be carried out very carefully. There are chances of accidents and since it involves dealing with high temperatures, welders need to be very careful. The welders are supposed to carry out the welding work in an area where there is no traces of water. The place where welding machine is placed and welding is done must be properly ventilated.

Welding is a process of heating the work pieces and joining them with a molten metal that forms a strong join after cooling. In order to heat the metals, energy sources like a gas flame, a laser or an electric arc can be used.

Due to the welding process, chemical fumes are emitted which are poisonous. The welders need to protect themselves from the poisonous emissions by masking their face. Thus, there is a great need to take have a proper air circulation system where the welding machine is placed.

Apart from the risk of inhaling poisonous gases, there are chances of fire accidents and visual impairment as well. A welder needs to wear personal protective equipment in order to protect himself. When you are welding, you should wear a long protective jacket and must protect your hands from burns by wearing leather gloves.

Your eyes are very sensitive and when exposed to bright arcs may lead to a condition called “arc eye”, where the cornea undergoes inflammation because of ultraviolet light. The ultraviolet rays emitted during welding process can cause damage to the cornea and retina in the eye. In order avoid damage to your eyes, you should wear goggles or welding helmets.

Not every homemade electric car projects require a welding machine. So before buying the welding machine there is a need to evaluate whether to buy or rent a welding machine. If the welding work is frequently being done in a period of time and there is further scope of use, you may consider buying a welding machine for your workshop. In doing so, investing in a new machine versus hiring skilled welder will prove to be a better option in the long run.

If welding is done infrequently, then renting a welding machine or hiring a welder will be apt. There are different costs associated with the welding works which are welding machine cost, labor cost, equipment cost, energy source cost, material cost and maintenance cost.

The welding equipment cost depends upon the methods being used. The cost of material is nothing but the cost of the metals that are used in welding can be quite expensive. The energy source cost can vary based on the source. Normally, gas flames are inexpensive when compared to laser or electric arc. The maintenance cost is the cost incurred to maintain, repair or service the welding machine.

Now that you know what’s involved in a welding process, you can now decide if you have to buy a new welding machine for your garage or outsource the welding work to a professional.